The key to productive measurement and analysis
Despite the often-high initial cost of top-quality metrology equipment, it is typically the longtail cost of manpower hours that is the most significant financial investment demanded by a rigorous quality control process. Operator interaction is also very often the major source of error within quality control processes. A system that can eliminate both the largest financial cost and the main source of errors is potentially well worth even significant initial investment.
Our laser tracker automated inspection solutions are inherently customised, built out according to very specific user requirements that define everything from size and components to initial and future functionalities. This bespoke approach is why our solutions are driving better quality and higher productivity in manufacturing instances all over the world.
6DoF with the AT960
The Leica Absolute Tracker AT960 is capable of six degrees of freedom (6DoF) measurement as standard, allowing the use of a scanner, camera or probe from up to 60 metres away. With the Leica T-Scan 5 Laser Scanner, APODIUS Absolute Camera AAC and Leica T-Mac sensors, this process can be automated, with each easily mountable on any standard industrial robot arm. Then a fully automated inspection setup is just a matter of programming and accessories, from turntables, sliders and robots to isolation walls, built-in control stations and tool changers for automatic sensor switching.
Direct Scanning with the ATS600
With the unique direct scanning functionality of the Leica Absolute Tracker ATS600, automated inspection is simpler than ever before. There’s no need for a sensor or an operator at the point of measurement, so components can just be brought into the tracker’s field of view and automatically inspected with just a few software clicks. No need to move the tracker, no need to manually scan. With its unique selective scanning functionality, you just tell the ATS600 the area it should measure and how much detail you need, and press start.
The ATS600 can even be mounted on an Automated Guided Vehicle (AGV) and run remotely through its Overview Camera. This allows its unique direct scanning ability, supported by reflector alignment with PowerLock, to span even greater measurement volumes.
Our laser tracker automated inspection solutions are inherently customised, built out according to very specific user requirements that define everything from size and components to initial and future functionalities. This bespoke approach is why our solutions are driving better quality and higher productivity in manufacturing instances all over the world.
6DoF with the AT960
The Leica Absolute Tracker AT960 is capable of six degrees of freedom (6DoF) measurement as standard, allowing the use of a scanner, camera or probe from up to 60 metres away. With the Leica T-Scan 5 Laser Scanner, APODIUS Absolute Camera AAC and Leica T-Mac sensors, this process can be automated, with each easily mountable on any standard industrial robot arm. Then a fully automated inspection setup is just a matter of programming and accessories, from turntables, sliders and robots to isolation walls, built-in control stations and tool changers for automatic sensor switching.
Direct Scanning with the ATS600
With the unique direct scanning functionality of the Leica Absolute Tracker ATS600, automated inspection is simpler than ever before. There’s no need for a sensor or an operator at the point of measurement, so components can just be brought into the tracker’s field of view and automatically inspected with just a few software clicks. No need to move the tracker, no need to manually scan. With its unique selective scanning functionality, you just tell the ATS600 the area it should measure and how much detail you need, and press start.
The ATS600 can even be mounted on an Automated Guided Vehicle (AGV) and run remotely through its Overview Camera. This allows its unique direct scanning ability, supported by reflector alignment with PowerLock, to span even greater measurement volumes.
Our Address
Dubai Office
Falcon Geomatics LLC
Ahammed Kamal Warehouse 6
Street 10C
Ras al Khor Industrial 1, Dubai
United Arab Emirates
Abu Dhabi Office
Falcon Geomatics LLC – Abu Dhabi
Musaffah Industrial Area M40
Plot Number 6 & Building 3
First Floor, Office No. 11 & 12
Abu Dhabi
United Arab Emirates
- +971 2 6777770
Quick Contact
- +971 4 327 9333 (Dubai)
- +971 4 2299555 (Dubai)
- +971 2 677 7770 (Abu Dhabi)
- sales@falcon-geosystems.com
- info@falcon-geosystems.com
- www.falcon-geosystems.com
- 08:00am to 06:00pm (Sat-Thu)
Copyright © 2021, Falcon Geomatics LLC – All Rights reserved